Printability

Generated by strido_verify.printability with PrusaSlicer-2.9.6 based on Slic3r (with GUI support) and hardware/print/prusaslicer.ini.

34 part types sliced as oriented in the kit, 13 plates sliced as arranged: 0 fail, 4 warn. Whole kit: 958 g PETG, 100 h printing (slicer estimate, all pieces).

Thin areas: lateral walls under 0.8 mm (two lines) or horizontal skins under 0.6 mm (three layers); 1 % percentile thickness per orientation.

Part	Qty	Supports	Brim	Time	Filament (g)	Thin lateral (mm²)	Thin skin (mm²)	Min wall / skin (mm)	Result	Slicer / notes
left_servo_mount	1	yes	no	2h 01m	18.0	12	22	1.54 / 0.42	warn	thin walls or skins: printable, but only one or two lines / layers thick
left_servo_mount_fl	1	yes	no	2h 01m	18.0	7	17	1.52 / 0.51	warn	thin walls or skins: printable, but only one or two lines / layers thick
right_servo_mount	1	yes	no	2h 01m	18.0	12	11	1.53 / 0.53	warn	thin walls or skins: printable, but only one or two lines / layers thick
right_servo_mount_fr	1	yes	no	2h 01m	18.0	12	26	1.52 / 0.38	warn	thin walls or skins: printable, but only one or two lines / layers thick
arming_port_bezel	1	no	no	0h 11m	1.4	0	0	0.50 / 1.00	ok
arming_port_ring	1	no	no	0h 07m	0.8	0	0	0.96 / 3.00	ok
back_shell_button	1	no	yes	4h 33m	53.0	0	0	1.64 / 2.00	ok
bottom_shell	1	yes	yes	8h 12m	76.2	0	0	1.00 / 1.97	ok
camera_mount_base	1	no	no	0h 45m	5.2	0	0	2.83 / 3.00	ok
camera_tilt_plate	1	yes	no	0h 40m	6.8	0	0	1.10 / 3.00	ok
display_bracket	1	no	no	1h 06m	9.5	0	0	1.82 / 3.00	ok
electronics_deck	1	yes	no	5h 11m	45.3	6	0	1.17 / 1.50	ok
femur	4	yes	no	2h 29m	24.6	0	0	2.36 / 0.73	ok
femur_servo_connector	4	yes	no	0h 17m	2.9	0	0	2.17 / 1.00	ok
foot_spacer	4	yes	no	0h 12m	1.9	0	0	0.83 / 1.16	ok
front_shell_display	1	no	yes	3h 40m	36.7	0	0	1.07 / 1.50	ok
hip_bearing_pin	4	no	no	0h 01m	0.1	3	0	0.58 / 0.65	ok
inner_shoulder_frame	2	no	no	2h 01m	17.7	0	0	0.97 / 2.00	ok
inner_tibia	4	yes	no	1h 40m	16.8	0	0	1.94 / 1.41	ok
left_shoulder	2	yes	no	1h 11m	12.6	9	0	1.04 / 1.50	ok
lidar_pedestal	1	no	no	2h 13m	20.8	0	0	2.79 / 3.00	ok
lower_shoulder_frame_front	1	no	no	1h 16m	11.5	0	0	0.96 / 0.77	ok
lower_shoulder_frame_rear	1	no	no	1h 16m	11.5	0	0	0.96 / 0.77	ok
outer_shoulder_frame	2	no	no	2h 19m	21.8	0	0	3.05 / 0.60	ok
outer_tibia	4	yes	no	1h 40m	16.7	0	0	1.37 / 1.30	ok
right_shoulder	2	yes	no	1h 12m	12.5	0	0	1.06 / 1.50	ok
servo_bus_holder_front	1	yes	no	1h 13m	11.4	0	0	1.60 / 0.60	ok
servo_bus_holder_rear	1	yes	no	0h 45m	6.8	0	0	1.54 / 0.60	ok	supports listed, but the slicer finds nothing to support
servo_mount_top_bracket	4	no	no	0h 26m	4.2	0	0	2.53 / 1.33	ok
short_link	4	yes	no	0h 13m	1.9	0	0	0.57 / 0.56	ok
side_body_beam	2	no	no	1h 33m	14.2	0	0	2.10 / 1.03	ok
stiff_long_link	4	no	no	0h 58m	10.8	0	0	1.00 / 10.00	ok
top_shell_sensor	1	yes	yes	8h 37m	77.2	0	0	1.00 / 1.97	ok
upper_shoulder_frame	2	no	no	1h 50m	17.9	0	0	1.40 / 0.95	ok

Plate	Result	Slicer
plate_graphite_01.3mf	ok
plate_graphite_02.3mf	ok
plate_graphite_03.3mf	ok
plate_graphite_04.3mf	ok
plate_graphite_05.3mf	ok
plate_graphite_06.3mf	ok
plate_graphite_07.3mf	ok
plate_graphite_08.3mf	ok
plate_graphite_09.3mf	ok
plate_graphite_10.3mf	ok
plate_lime_01.3mf	ok
plate_lime_02.3mf	ok
plate_lime_03.3mf	ok